Catching up Sharingan, Geth, and ShadowArch roles

roles/Geth-Hub/templates/modules.j2

@@ -3,8 +3,8 @@
 # This file contains the names of kernel modules that should be loaded
 # at boot time, one per line. Lines beginning with "#" are ignored.
 
-lirc_dev
-lirc_rpi gpio_in_pin={{ gpio_in_pin | default('18') }} gpio_out_pin={{ gpio_out_pin | default('17') }}
+# lirc_dev
+# lirc_rpi gpio_in_pin={{ gpio_in_pin | default('18') }} gpio_out_pin={{ gpio_out_pin | default('17') }}
 bcm2835-v4l2
 r8188eu
 

roles/Geth-Hub/templates/motion.conf.j2

@@ -0,0 +1,176 @@
+# Rename this distribution example file to motion.conf
+#
+# This config file was generated by motion 4.3.2
+# Documentation:  /usr/share/doc/motion/motion_guide.html
+#
+# This file contains only the basic configuration options to get a
+# system working.  There are many more options available.  Please
+# consult the documentation for the complete list of all options.
+#
+
+############################################################
+# System control configuration parameters
+############################################################
+
+# Start in daemon (background) mode and release terminal.
+daemon off
+
+# Start in Setup-Mode, daemon disabled.
+setup_mode off
+
+# File to store the process ID.
+; pid_file value
+
+# File to write logs messages into.  If not defined stderr and syslog is used.
+log_file /var/log/motion/motion.log
+
+# Level of log messages [1..9] (EMG, ALR, CRT, ERR, WRN, NTC, INF, DBG, ALL).
+log_level 6
+
+# Target directory for pictures, snapshots and movies
+target_dir /var/lib/motion
+
+# Video device (e.g. /dev/video0) to be used for capturing.
+videodevice /dev/video0
+
+# Parameters to control video device.  See motion_guide.html
+; vid_control_params value
+
+# The full URL of the network camera stream.
+; netcam_url value
+
+# Name of mmal camera (e.g. vc.ril.camera for pi camera).
+; mmalcam_name value
+mmalcam_name vc.ril.camera
+mmalcam_use_still off
+
+# Camera control parameters (see raspivid/raspistill tool documentation)
+; mmalcam_control_params value
+
+############################################################
+# Image Processing configuration parameters
+############################################################
+
+# Image width in pixels.
+width 1296
+
+# Image height in pixels.
+height 972
+
+# Maximum number of frames to be captured per second.
+framerate 15
+
+# Rotate to fit
+rotate {{ rotate }}
+
+# Text to be overlayed in the lower left corner of images
+text_left {{ inventory_hostname }}
+
+# Text to be overlayed in the lower right corner of images.
+text_right %Y-%m-%d\n%T-%q
+
+############################################################
+# Motion detection configuration parameters
+############################################################
+
+# Always save pictures and movies even if there was no motion.
+emulate_motion off
+
+# Threshold for number of changed pixels that triggers motion.
+threshold 1500
+
+# Noise threshold for the motion detection.
+; noise_level 32
+
+# Despeckle the image using (E/e)rode or (D/d)ilate or (l)abel.
+despeckle_filter EedDl
+
+# Number of images that must contain motion to trigger an event.
+minimum_motion_frames 1
+
+# Gap in seconds of no motion detected that triggers the end of an event.
+event_gap 60
+
+# The number of pre-captured (buffered) pictures from before motion.
+pre_capture 3
+
+# Number of frames to capture after motion is no longer detected.
+post_capture 0
+
+############################################################
+# Script execution configuration parameters
+############################################################
+
+# Command to be executed when an event starts.
+; on_event_start value
+
+# Command to be executed when an event ends.
+; on_event_end value
+
+# Command to be executed when a movie file is closed.
+; on_movie_end value
+
+############################################################
+# Picture output configuration parameters
+############################################################
+
+# Output pictures when motion is detected
+picture_output off
+
+# File name(without extension) for pictures relative to target directory
+picture_filename %Y%m%d%H%M%S-%q
+
+############################################################
+# Movie output configuration parameters
+############################################################
+
+# Create movies of motion events.
+movie_output off
+
+# Maximum length of movie in seconds.
+movie_max_time 60
+
+# The encoding quality of the movie. (0=use bitrate. 1=worst quality, 100=best)
+movie_quality 45
+
+# Container/Codec to used for the movie. See motion_guide.html
+movie_codec mkv
+
+# File name(without extension) for movies relative to target directory
+movie_filename %t-%v-%Y%m%d%H%M%S
+
+############################################################
+# Webcontrol configuration parameters
+############################################################
+
+# Port number used for the webcontrol.
+webcontrol_port 8080
+
+# Restrict webcontrol connections to the localhost.
+webcontrol_localhost on
+
+# Type of configuration options to allow via the webcontrol.
+webcontrol_parms 0
+
+############################################################
+# Live stream configuration parameters
+############################################################
+
+# The port number for the live stream.
+stream_port 8081
+
+# Restrict stream connections to the localhost.
+stream_localhost off
+
+##############################################################
+# Camera config files - One for each camera.
+##############################################################
+; camera /usr/etc/motion/camera1.conf
+; camera /usr/etc/motion/camera2.conf
+; camera /usr/etc/motion/camera3.conf
+; camera /usr/etc/motion/camera4.conf
+
+##############################################################
+# Directory to read '.conf' files for cameras.
+##############################################################
+; camera_dir /usr/etc/motion/conf.d