1328 lines
49 KiB
YAML
1328 lines
49 KiB
YAML
%YAML 1.1
|
|
---
|
|
|
|
# Suricata configuration file. In addition to the comments describing all
|
|
# options in this file, full documentation can be found at:
|
|
# https://redmine.openinfosecfoundation.org/projects/suricata/wiki/Suricatayaml
|
|
|
|
|
|
# Number of packets allowed to be processed simultaneously. Default is a
|
|
# conservative 1024. A higher number will make sure CPU's/CPU cores will be
|
|
# more easily kept busy, but may negatively impact caching.
|
|
#
|
|
# If you are using the CUDA pattern matcher (mpm-algo: ac-cuda), different rules
|
|
# apply. In that case try somenp1s0fing like 60000 or more. This is because the CUDA
|
|
# pattern matcher buffers and scans as many packets as possible in parallel.
|
|
#max-pending-packets: 1024
|
|
|
|
# Runmode the engine should use. Please check --list-runmodes to get the available
|
|
# runmodes for each packet acquisition menp1s0fod. Defaults to "autofp" (auto flow pinned
|
|
# load balancing).
|
|
#runmode: autofp
|
|
|
|
# Specifies the kind of flow load balancer used by the flow pinned autofp mode.
|
|
#
|
|
# Supported schedulers are:
|
|
#
|
|
# round-robin - Flows assigned to threads in a round robin fashion.
|
|
# active-packets - Flows assigned to threads that have the lowest number of
|
|
# unprocessed packets (default).
|
|
# hash - Flow alloted usihng the address hash. More of a random
|
|
# technique. Was the default in Suricata 1.2.1 and older.
|
|
#
|
|
#autofp-scheduler: active-packets
|
|
|
|
# If suricata box is a router for the sniffed networks, set it to 'router'. If
|
|
# it is a pure sniffing setup, set it to 'sniffer-only'.
|
|
# If set to auto, the variable is internally switch to 'router' in IPS mode
|
|
# and 'sniffer-only' in IDS mode.
|
|
# This feature is currently only used by the reject* keywords.
|
|
host-mode: auto
|
|
|
|
# Run suricata as user and group.
|
|
#run-as:
|
|
#user: suricata
|
|
#group: suricata
|
|
|
|
# Default pid file.
|
|
# Will use this file if no --pidfile in command options.
|
|
#pid-file: /var/run/suricata.pid
|
|
|
|
# Daemon working directory
|
|
# Suricata will change directory to this one if provided
|
|
# Default: "/"
|
|
#daemon-directory: "/"
|
|
|
|
# Preallocated size for packet. Default is 1514 which is the classical
|
|
# size for pcap on enp1s0fernet. You should adjust this value to the highest
|
|
# packet size (MTU + hardware header) on your system.
|
|
#default-packet-size: 1514
|
|
|
|
# The default logging directory. Any log or output file will be
|
|
# placed here if its not specified with a full path name. This can be
|
|
# overridden with the -l command line parameter.
|
|
default-log-dir: /var/log/suricata/
|
|
|
|
# Unix command socket can be used to pass commands to suricata.
|
|
# An external tool can then connect to get information from suricata
|
|
# or trigger some modifications of the engine. Set enabled to yes
|
|
# to activate the feature. You can use the filename variable to set
|
|
# the file name of the socket.
|
|
unix-command:
|
|
enabled: no
|
|
#filename: custom.socket
|
|
|
|
# Configure the type of alert (and other) logging you would like.
|
|
outputs:
|
|
|
|
# a line based alerts log similar to Snort's fast.log
|
|
- fast:
|
|
enabled: no
|
|
filename: fast.log
|
|
append: yes
|
|
#filetype: regular # 'regular', 'unix_stream' or 'unix_dgram'
|
|
|
|
# Extensible Event Format (nicknamed EVE) event log in JSON format
|
|
- eve-log:
|
|
enabled: no
|
|
type: file #file|syslog|unix_dgram|unix_stream
|
|
filename: eve.json
|
|
# the following are valid when type: syslog above
|
|
#identity: "suricata"
|
|
#facility: local5
|
|
#level: Info ## possible levels: Emergency, Alert, Critical,
|
|
## Error, Warning, Notice, Info, Debug
|
|
types:
|
|
- alert
|
|
- http:
|
|
extended: yes # enable this for extended logging information
|
|
# custom allows additional http fields to be included in eve-log
|
|
# the example below adds three additional fields when uncommented
|
|
#custom: [Accept-Encoding, Accept-Language, Authorization]
|
|
- dns
|
|
- tls:
|
|
extended: yes # enable this for extended logging information
|
|
- files:
|
|
force-magic: no # force logging magic on all logged files
|
|
force-hash: [md5] # force logging of md5 checksums
|
|
#- drop
|
|
- ssh
|
|
|
|
# alert output for use with Barnyard2
|
|
- unified2-alert:
|
|
enabled: no
|
|
filename: unified2.alert
|
|
|
|
# File size limit. Can be specified in kb, mb, gb. Just a number
|
|
# is parsed as bytes.
|
|
#limit: 32mb
|
|
|
|
# Sensor ID field of unified2 alerts.
|
|
#sensor-id: 0
|
|
|
|
# HTTP X-Forwarded-For support by adding the unified2 extra header that
|
|
# will contain the actual client IP address or by overwriting the source
|
|
# IP address (helpful when inspecting traffic that is being reversed
|
|
# proxied).
|
|
xff:
|
|
enabled: no
|
|
# Two operation modes are available, "extra-data" and "overwrite". Note
|
|
# that in the "overwrite" mode, if the reported IP address in the HTTP
|
|
# X-Forwarded-For header is of a different version of the packet
|
|
# received, it will fall-back to "extra-data" mode.
|
|
mode: extra-data
|
|
# Header name were the actual IP address will be reported, if more than
|
|
# one IP address is present, the last IP address will be the one taken
|
|
# into consideration.
|
|
header: X-Forwarded-For
|
|
|
|
# a line based log of HTTP requests (no alerts)
|
|
- http-log:
|
|
enabled: no
|
|
filename: http.log
|
|
append: yes
|
|
#extended: yes # enable this for extended logging information
|
|
#custom: yes # enabled the custom logging format (defined by customformat)
|
|
#customformat: "%{%D-%H:%M:%S}t.%z %{X-Forwarded-For}i %H %m %h %u %s %B %a:%p -> %A:%P"
|
|
#filetype: regular # 'regular', 'unix_stream' or 'unix_dgram'
|
|
|
|
# a line based log of TLS handshake parameters (no alerts)
|
|
- tls-log:
|
|
enabled: no # Log TLS connections.
|
|
filename: tls.log # File to store TLS logs.
|
|
append: yes
|
|
#filetype: regular # 'regular', 'unix_stream' or 'unix_dgram'
|
|
#extended: yes # Log extended information like fingerprint
|
|
certs-log-dir: certs # directory to store the certificates files
|
|
|
|
# a line based log of DNS requests and/or replies (no alerts)
|
|
- dns-log:
|
|
enabled: no
|
|
filename: dns.log
|
|
append: yes
|
|
#filetype: regular # 'regular', 'unix_stream' or 'unix_dgram'
|
|
|
|
# a line based log to used with pcap file study.
|
|
# this module is dedicated to offline pcap parsing (empty output
|
|
# if used with another kind of input). It can interoperate with
|
|
# pcap parser like wireshark via the suriwire plugin.
|
|
- pcap-info:
|
|
enabled: no
|
|
|
|
# Packet log... log packets in pcap format. 2 modes of operation: "normal"
|
|
# and "sguil".
|
|
#
|
|
# In normal mode a pcap file "filename" is created in the default-log-dir,
|
|
# or are as specified by "dir". In Sguil mode "dir" indicates the base directory.
|
|
# In this base dir the pcaps are created in th directory structure Sguil expects:
|
|
#
|
|
# $sguil-base-dir/YYYY-MM-DD/$filename.<timestamp>
|
|
#
|
|
# By default all packets are logged except:
|
|
# - TCP streams beyond stream.reassembly.depth
|
|
# - encrypted streams after the key exchange
|
|
#
|
|
- pcap-log:
|
|
enabled: no
|
|
filename: log.pcap
|
|
|
|
# File size limit. Can be specified in kb, mb, gb. Just a number
|
|
# is parsed as bytes.
|
|
limit: 1000mb
|
|
|
|
# If set to a value will enable ring buffer mode. Will keep Maximum of "max-files" of size "limit"
|
|
max-files: 2000
|
|
|
|
mode: normal # normal or sguil.
|
|
#sguil-base-dir: /nsm_data/
|
|
#ts-format: usec # sec or usec second format (default) is filename.sec usec is filename.sec.usec
|
|
use-stream-depth: no #If set to "yes" packets seen after reaching stream inspection depth are ignored. "no" logs all packets
|
|
|
|
# a full alerts log containing much information for signature writers
|
|
# or for investigating suspected false positives.
|
|
- alert-debug:
|
|
enabled: no
|
|
filename: alert-debug.log
|
|
append: yes
|
|
#filetype: regular # 'regular', 'unix_stream' or 'unix_dgram'
|
|
|
|
# alert output to prelude (http://www.prelude-technologies.com/) only
|
|
# available if Suricata has been compiled with --enable-prelude
|
|
- alert-prelude:
|
|
enabled: no
|
|
profile: suricata
|
|
log-packet-content: no
|
|
log-packet-header: yes
|
|
|
|
# Stats.log contains data from various counters of the suricata engine.
|
|
# The interval field (in seconds) tells after how long output will be written
|
|
# on the log file.
|
|
- stats:
|
|
enabled: yes
|
|
filename: stats.log
|
|
interval: 8
|
|
|
|
# a line based alerts log similar to fast.log into syslog
|
|
- syslog:
|
|
enabled: yes
|
|
# reported identity to syslog. If ommited the program name (usually
|
|
# suricata) will be used.
|
|
identity: "sharingan-nids"
|
|
facility: local5
|
|
#level: Info ## possible levels: Emergency, Alert, Critical,
|
|
## Error, Warning, Notice, Info, Debug
|
|
|
|
# a line based information for dropped packets in IPS mode
|
|
- drop:
|
|
enabled: no
|
|
filename: drop.log
|
|
append: yes
|
|
#filetype: regular # 'regular', 'unix_stream' or 'unix_dgram'
|
|
|
|
# output module to store extracted files to disk
|
|
#
|
|
# The files are stored to the log-dir in a format "file.<id>" where <id> is
|
|
# an incrementing number starting at 1. For each file "file.<id>" a meta
|
|
# file "file.<id>.meta" is created.
|
|
#
|
|
# File extraction depends on a lot of things to be fully done:
|
|
# - stream reassembly depth. For optimal results, set this to 0 (unlimited)
|
|
# - http request / response body sizes. Again set to 0 for optimal results.
|
|
# - rules that contain the "filestore" keyword.
|
|
- file-store:
|
|
enabled: no # set to yes to enable
|
|
log-dir: files # directory to store the files
|
|
force-magic: no # force logging magic on all stored files
|
|
force-md5: no # force logging of md5 checksums
|
|
#waldo: file.waldo # waldo file to store the file_id across runs
|
|
|
|
# output module to log files tracked in a easily parsable json format
|
|
- file-log:
|
|
enabled: no
|
|
filename: files-json.log
|
|
append: yes
|
|
#filetype: regular # 'regular', 'unix_stream' or 'unix_dgram'
|
|
|
|
force-magic: no # force logging magic on all logged files
|
|
force-md5: no # force logging of md5 checksums
|
|
|
|
# Magic file. The extension .mgc is added to the value here.
|
|
#magic-file: /usr/share/file/magic
|
|
magic-file: /usr/share/file/misc/magic.mgc
|
|
|
|
# When running in NFQ inline mode, it is possible to use a simulated
|
|
# non-terminal NFQUEUE verdict.
|
|
# This permit to do send all needed packet to suricata via this a rule:
|
|
# iptables -I FORWARD -m mark ! --mark $MARK/$MASK -j NFQUEUE
|
|
# And below, you can have your standard filtering ruleset. To activate
|
|
# this mode, you need to set mode to 'repeat'
|
|
# If you want packet to be sent to another queue after an ACCEPT decision
|
|
# set mode to 'route' and set next-queue value.
|
|
# On linux >= 3.1, you can set batchcount to a value > 1 to improve performance
|
|
# by processing several packets before sending a verdict (worker runmode only).
|
|
# On linux >= 3.6, you can set the fail-open option to yes to have the kernel
|
|
# accept the packet if suricata is not able to keep pace.
|
|
nfq:
|
|
# mode: accept
|
|
# repeat-mark: 1
|
|
# repeat-mask: 1
|
|
# route-queue: 2
|
|
# batchcount: 20
|
|
# fail-open: yes
|
|
|
|
#nflog support
|
|
nflog:
|
|
# netlink multicast group
|
|
# (the same as the iptables --nflog-group param)
|
|
# Group 0 is used by the kernel, so you can't use it
|
|
- group: 2
|
|
# netlink buffer size
|
|
buffer-size: 18432
|
|
# put default value here
|
|
- group: default
|
|
# set number of packet to queue inside kernel
|
|
qthreshold: 1
|
|
# set the delay before flushing packet in the queue inside kernel
|
|
qtimeout: 100
|
|
# netlink max buffer size
|
|
max-size: 20000
|
|
|
|
# af-packet support
|
|
# Set threads to > 1 to use PACKET_FANOUT support
|
|
af-packet:
|
|
- interface: enp1s0f0
|
|
# Number of receive threads (>1 will enable experimental flow pinned
|
|
# runmode)
|
|
threads: 1
|
|
# Default clusterid. AF_PACKET will load balance packets based on flow.
|
|
# All threads/processes that will participate need to have the same
|
|
# clusterid.
|
|
cluster-id: 99
|
|
# Default AF_PACKET cluster type. AF_PACKET can load balance per flow or per hash.
|
|
# This is only supported for Linux kernel > 3.1
|
|
# possible value are:
|
|
# * cluster_round_robin: round robin load balancing
|
|
# * cluster_flow: all packets of a given flow are send to the same socket
|
|
# * cluster_cpu: all packets treated in kernel by a CPU are send to the same socket
|
|
cluster-type: cluster_flow
|
|
# In some fragmentation case, the hash can not be computed. If "defrag" is set
|
|
# to yes, the kernel will do the needed defragmentation before sending the packets.
|
|
defrag: yes
|
|
# To use the ring feature of AF_PACKET, set 'use-mmap' to yes
|
|
use-mmap: yes
|
|
# Ring size will be computed with respect to max_pending_packets and number
|
|
# of threads. You can set manually the ring size in number of packets by setting
|
|
# the following value. If you are using flow cluster-type and have really network
|
|
# intensive single-flow you could want to set the ring-size independantly of the number
|
|
# of threads:
|
|
#ring-size: 2048
|
|
# On busy system, this could help to set it to yes to recover from a packet drop
|
|
# phase. This will result in some packets (at max a ring flush) being non treated.
|
|
#use-emergency-flush: yes
|
|
# recv buffer size, increase value could improve performance
|
|
# buffer-size: 32768
|
|
# Set to yes to disable promiscuous mode
|
|
# disable-promisc: no
|
|
# Choose checksum verification mode for the interface. At the moment
|
|
# of the capture, some packets may be with an invalid checksum due to
|
|
# offloading to the network card of the checksum computation.
|
|
# Possible values are:
|
|
# - kernel: use indication sent by kernel for each packet (default)
|
|
# - yes: checksum validation is forced
|
|
# - no: checksum validation is disabled
|
|
# - auto: suricata uses a statistical approach to detect when
|
|
# checksum off-loading is used.
|
|
# Warning: 'checksum-validation' must be set to yes to have any validation
|
|
#checksum-checks: kernel
|
|
# BPF filter to apply to this interface. The pcap filter syntax apply here.
|
|
#bpf-filter: port 80 or udp
|
|
# You can use the following variables to activate AF_PACKET tap od IPS mode.
|
|
# If copy-mode is set to ips or tap, the traffic coming to the current
|
|
# interface will be copied to the copy-iface interface. If 'tap' is set, the
|
|
# copy is complete. If 'ips' is set, the packet matching a 'drop' action
|
|
# will not be copied.
|
|
#copy-mode: ips
|
|
#copy-iface: enp1s0f1
|
|
- interface: enp1s0f1
|
|
threads: 1
|
|
cluster-id: 98
|
|
cluster-type: cluster_flow
|
|
defrag: yes
|
|
# buffer-size: 32768
|
|
# disable-promisc: no
|
|
# Put default values here
|
|
- interface: default
|
|
#threads: 2
|
|
#use-mmap: yes
|
|
|
|
legacy:
|
|
uricontent: enabled
|
|
|
|
# You can specify a threshold config file by setting "threshold-file"
|
|
# to the path of the threshold config file:
|
|
# threshold-file: /etc/suricata/threshold.config
|
|
|
|
# The detection engine builds internal groups of signatures. The engine
|
|
# allow us to specify the profile to use for them, to manage memory on an
|
|
# efficient way keeping a good performance. For the profile keyword you
|
|
# can use the words "low", "medium", "high" or "custom". If you use custom
|
|
# make sure to define the values at "- custom-values" as your convenience.
|
|
# Usually you would prefer medium/high/low.
|
|
#
|
|
# "sgh mpm-context", indicates how the staging should allot mpm contexts for
|
|
# the signature groups. "single" indicates the use of a single context for
|
|
# all the signature group heads. "full" indicates a mpm-context for each
|
|
# group head. "auto" lets the engine decide the distribution of contexts
|
|
# based on the information the engine gathers on the patterns from each
|
|
# group head.
|
|
#
|
|
# The option inspection-recursion-limit is used to limit the recursive calls
|
|
# in the content inspection code. For certain payload-sig combinations, we
|
|
# might end up taking too much time in the content inspection code.
|
|
# If the argument specified is 0, the engine uses an internally defined
|
|
# default limit. On not specifying a value, we use no limits on the recursion.
|
|
detect-engine:
|
|
- profile: medium
|
|
- custom-values:
|
|
toclient-src-groups: 2
|
|
toclient-dst-groups: 2
|
|
toclient-sp-groups: 2
|
|
toclient-dp-groups: 3
|
|
toserver-src-groups: 2
|
|
toserver-dst-groups: 4
|
|
toserver-sp-groups: 2
|
|
toserver-dp-groups: 25
|
|
- sgh-mpm-context: auto
|
|
- inspection-recursion-limit: 3000
|
|
# When rule-reload is enabled, sending a USR2 signal to the Suricata process
|
|
# will trigger a live rule reload. Experimental feature, use with care.
|
|
#- rule-reload: true
|
|
# If set to yes, the loading of signatures will be made after the capture
|
|
# is started. This will limit the downtime in IPS mode.
|
|
#- delayed-detect: yes
|
|
|
|
# Suricata is multi-threaded. Here the threading can be influenced.
|
|
threading:
|
|
# On some cpu's/architectures it is beneficial to tie individual threads
|
|
# to specific CPU's/CPU cores. In this case all threads are tied to CPU0,
|
|
# and each extra CPU/core has one "detect" thread.
|
|
#
|
|
# On Intel Core2 and Nehalem CPU's enabling this will degrade performance.
|
|
#
|
|
set-cpu-affinity: no
|
|
# Tune cpu affinity of suricata threads. Each family of threads can be bound
|
|
# on specific CPUs.
|
|
cpu-affinity:
|
|
- management-cpu-set:
|
|
cpu: [ 0 ] # include only these cpus in affinity settings
|
|
- receive-cpu-set:
|
|
cpu: [ 0 ] # include only these cpus in affinity settings
|
|
- decode-cpu-set:
|
|
cpu: [ 0, 1 ]
|
|
mode: "balanced"
|
|
- stream-cpu-set:
|
|
cpu: [ "0-1" ]
|
|
- detect-cpu-set:
|
|
cpu: [ "all" ]
|
|
mode: "exclusive" # run detect threads in these cpus
|
|
# Use explicitely 3 threads and don't compute number by using
|
|
# detect-thread-ratio variable:
|
|
# threads: 3
|
|
prio:
|
|
low: [ 0 ]
|
|
medium: [ "1-2" ]
|
|
high: [ 3 ]
|
|
default: "medium"
|
|
- verdict-cpu-set:
|
|
cpu: [ 0 ]
|
|
prio:
|
|
default: "high"
|
|
- reject-cpu-set:
|
|
cpu: [ 0 ]
|
|
prio:
|
|
default: "low"
|
|
- output-cpu-set:
|
|
cpu: [ "all" ]
|
|
prio:
|
|
default: "medium"
|
|
#
|
|
# By default Suricata creates one "detect" thread per available CPU/CPU core.
|
|
# This setting allows controlling this behaviour. A ratio setting of 2 will
|
|
# create 2 detect threads for each CPU/CPU core. So for a dual core CPU this
|
|
# will result in 4 detect threads. If values below 1 are used, less threads
|
|
# are created. So on a dual core CPU a setting of 0.5 results in 1 detect
|
|
# thread being created. Regardless of the setting at a minimum 1 detect
|
|
# thread will always be created.
|
|
#
|
|
detect-thread-ratio: 1.5
|
|
|
|
# Cuda configuration.
|
|
cuda:
|
|
# The "mpm" profile. On not specifying any of these parameters, the engine's
|
|
# internal default values are used, which are same as the ones specified in
|
|
# in the default conf file.
|
|
mpm:
|
|
# The minimum length required to buffer data to the gpu.
|
|
# Anything below this is MPM'ed on the CPU.
|
|
# Can be specified in kb, mb, gb. Just a number indicates it's in bytes.
|
|
# A value of 0 indicates there's no limit.
|
|
data-buffer-size-min-limit: 0
|
|
# The maximum length for data that we would buffer to the gpu.
|
|
# Anything over this is MPM'ed on the CPU.
|
|
# Can be specified in kb, mb, gb. Just a number indicates it's in bytes.
|
|
data-buffer-size-max-limit: 1500
|
|
# The ring buffer size used by the CudaBuffer API to buffer data.
|
|
cudabuffer-buffer-size: 500mb
|
|
# The max chunk size that can be sent to the gpu in a single go.
|
|
gpu-transfer-size: 50mb
|
|
# The timeout limit for batching of packets in microseconds.
|
|
batching-timeout: 2000
|
|
# The device to use for the mpm. Currently we don't support load balancing
|
|
# on multiple gpus. In case you have multiple devices on your system, you
|
|
# can specify the device to use, using this conf. By default we hold 0, to
|
|
# specify the first device cuda sees. To find out device-id associated with
|
|
# the card(s) on the system run "suricata --list-cuda-cards".
|
|
device-id: 0
|
|
# No of Cuda streams used for asynchronous processing. All values > 0 are valid.
|
|
# For this option you need a device with Compute Capability > 1.0.
|
|
cuda-streams: 2
|
|
|
|
# Select the multi pattern algorithm you want to run for scan/search the
|
|
# in the engine. The supported algorithms are b2g, b2gc, b2gm, b3g, wumanber,
|
|
# ac and ac-gfbs.
|
|
#
|
|
# The mpm you choose also decides the distribution of mpm contexts for
|
|
# signature groups, specified by the conf - "detect-engine.sgh-mpm-context".
|
|
# Selecting "ac" as the mpm would require "detect-engine.sgh-mpm-context"
|
|
# to be set to "single", because of ac's memory requirements, unless the
|
|
# ruleset is small enough to fit in one's memory, in which case one can
|
|
# use "full" with "ac". Rest of the mpms can be run in "full" mode.
|
|
#
|
|
# There is also a CUDA pattern matcher (only available if Suricata was
|
|
# compiled with --enable-cuda: b2g_cuda. Make sure to update your
|
|
# max-pending-packets setting above as well if you use b2g_cuda.
|
|
|
|
mpm-algo: ac
|
|
|
|
# The memory settings for hash size of these algorithms can vary from lowest
|
|
# (2048) - low (4096) - medium (8192) - high (16384) - higher (32768) - max
|
|
# (65536). The bloomfilter sizes of these algorithms can vary from low (512) -
|
|
# medium (1024) - high (2048).
|
|
#
|
|
# For B2g/B3g algorithms, there is a support for two different scan/search
|
|
# algorithms. For B2g the scan algorithms are B2gScan & B2gScanBNDMq, and
|
|
# search algorithms are B2gSearch & B2gSearchBNDMq. For B3g scan algorithms
|
|
# are B3gScan & B3gScanBNDMq, and search algorithms are B3gSearch &
|
|
# B3gSearchBNDMq.
|
|
#
|
|
# For B2g the different scan/search algorithms and, hash and bloom
|
|
# filter size settings. For B3g the different scan/search algorithms and, hash
|
|
# and bloom filter size settings. For wumanber the hash and bloom filter size
|
|
# settings.
|
|
|
|
pattern-matcher:
|
|
- b2gc:
|
|
search-algo: B2gSearchBNDMq
|
|
hash-size: low
|
|
bf-size: medium
|
|
- b2gm:
|
|
search-algo: B2gSearchBNDMq
|
|
hash-size: low
|
|
bf-size: medium
|
|
- b2g:
|
|
search-algo: B2gSearchBNDMq
|
|
hash-size: low
|
|
bf-size: medium
|
|
- b3g:
|
|
search-algo: B3gSearchBNDMq
|
|
hash-size: low
|
|
bf-size: medium
|
|
- wumanber:
|
|
hash-size: low
|
|
bf-size: medium
|
|
|
|
# Defrag settings:
|
|
|
|
defrag:
|
|
memcap: 32mb
|
|
hash-size: 65536
|
|
trackers: 65535 # number of defragmented flows to follow
|
|
max-frags: 65535 # number of fragments to keep (higher than trackers)
|
|
prealloc: yes
|
|
timeout: 60
|
|
|
|
# Enable defrag per host settings
|
|
# host-config:
|
|
#
|
|
# - dmz:
|
|
# timeout: 30
|
|
# address: [192.168.1.0/24, 127.0.0.0/8, 1.1.1.0/24, 2.2.2.0/24, "1.1.1.1", "2.2.2.2", "::1"]
|
|
#
|
|
# - lan:
|
|
# timeout: 45
|
|
# address:
|
|
# - 192.168.0.0/24
|
|
# - 192.168.10.0/24
|
|
# - 172.16.14.0/24
|
|
|
|
# Flow settings:
|
|
# By default, the reserved memory (memcap) for flows is 32MB. This is the limit
|
|
# for flow allocation inside the engine. You can change this value to allow
|
|
# more memory usage for flows.
|
|
# The hash-size determine the size of the hash used to identify flows inside
|
|
# the engine, and by default the value is 65536.
|
|
# At the startup, the engine can preallocate a number of flows, to get a better
|
|
# performance. The number of flows preallocated is 10000 by default.
|
|
# emergency-recovery is the percentage of flows that the engine need to
|
|
# prune before unsetting the emergency state. The emergency state is activated
|
|
# when the memcap limit is reached, allowing to create new flows, but
|
|
# prunning them with the emergency timeouts (they are defined below).
|
|
# If the memcap is reached, the engine will try to prune flows
|
|
# with the default timeouts. If it doens't find a flow to prune, it will set
|
|
# the emergency bit and it will try again with more agressive timeouts.
|
|
# If that doesn't work, then it will try to kill the last time seen flows
|
|
# not in use.
|
|
# The memcap can be specified in kb, mb, gb. Just a number indicates it's
|
|
# in bytes.
|
|
|
|
flow:
|
|
memcap: 64mb
|
|
hash-size: 65536
|
|
prealloc: 10000
|
|
emergency-recovery: 30
|
|
|
|
# This option controls the use of vlan ids in the flow (and defrag)
|
|
# hashing. Normally this should be enabled, but in some (broken)
|
|
# setups where both sides of a flow are not tagged with the same vlan
|
|
# tag, we can ignore the vlan id's in the flow hashing.
|
|
vlan:
|
|
use-for-tracking: true
|
|
|
|
# Specific timeouts for flows. Here you can specify the timeouts that the
|
|
# active flows will wait to transit from the current state to another, on each
|
|
# protocol. The value of "new" determine the seconds to wait after a hanshake or
|
|
# stream startup before the engine free the data of that flow it doesn't
|
|
# change the state to established (usually if we don't receive more packets
|
|
# of that flow). The value of "established" is the amount of
|
|
# seconds that the engine will wait to free the flow if it spend that amount
|
|
# without receiving new packets or closing the connection. "closed" is the
|
|
# amount of time to wait after a flow is closed (usually zero).
|
|
#
|
|
# There's an emergency mode that will become active under attack circumstances,
|
|
# making the engine to check flow status faster. This configuration variables
|
|
# use the prefix "emergency-" and work similar as the normal ones.
|
|
# Some timeouts doesn't apply to all the protocols, like "closed", for udp and
|
|
# icmp.
|
|
|
|
flow-timeouts:
|
|
|
|
default:
|
|
new: 30
|
|
established: 300
|
|
closed: 0
|
|
emergency-new: 10
|
|
emergency-established: 100
|
|
emergency-closed: 0
|
|
tcp:
|
|
new: 60
|
|
established: 3600
|
|
closed: 120
|
|
emergency-new: 10
|
|
emergency-established: 300
|
|
emergency-closed: 20
|
|
udp:
|
|
new: 30
|
|
established: 300
|
|
emergency-new: 10
|
|
emergency-established: 100
|
|
icmp:
|
|
new: 30
|
|
established: 300
|
|
emergency-new: 10
|
|
emergency-established: 100
|
|
|
|
# Stream engine settings. Here the TCP stream tracking and reassembly
|
|
# engine is configured.
|
|
#
|
|
# stream:
|
|
# memcap: 32mb # Can be specified in kb, mb, gb. Just a
|
|
# # number indicates it's in bytes.
|
|
# checksum-validation: yes # To validate the checksum of received
|
|
# # packet. If csum validation is specified as
|
|
# # "yes", then packet with invalid csum will not
|
|
# # be processed by the engine stream/app layer.
|
|
# # Warning: locally generated trafic can be
|
|
# # generated without checksum due to hardware offload
|
|
# # of checksum. You can control the handling of checksum
|
|
# # on a per-interface basis via the 'checksum-checks'
|
|
# # option
|
|
# prealloc-sessions: 2k # 2k sessions prealloc'd per stream thread
|
|
# midstream: false # don't allow midstream session pickups
|
|
# async-oneside: false # don't enable async stream handling
|
|
# inline: no # stream inline mode
|
|
# max-synack-queued: 5 # Max different SYN/ACKs to queue
|
|
#
|
|
# reassembly:
|
|
# memcap: 64mb # Can be specified in kb, mb, gb. Just a number
|
|
# # indicates it's in bytes.
|
|
# depth: 1mb # Can be specified in kb, mb, gb. Just a number
|
|
# # indicates it's in bytes.
|
|
# toserver-chunk-size: 2560 # inspect raw stream in chunks of at least
|
|
# # this size. Can be specified in kb, mb,
|
|
# # gb. Just a number indicates it's in bytes.
|
|
# # The max acceptable size is 4024 bytes.
|
|
# toclient-chunk-size: 2560 # inspect raw stream in chunks of at least
|
|
# # this size. Can be specified in kb, mb,
|
|
# # gb. Just a number indicates it's in bytes.
|
|
# # The max acceptable size is 4024 bytes.
|
|
# randomize-chunk-size: yes # Take a random value for chunk size around the specified value.
|
|
# # This lower the risk of some evasion technics but could lead
|
|
# # detection change between runs. It is set to 'yes' by default.
|
|
# randomize-chunk-range: 10 # If randomize-chunk-size is active, the value of chunk-size is
|
|
# # a random value between (1 - randomize-chunk-range/100)*randomize-chunk-size
|
|
# # and (1 + randomize-chunk-range/100)*randomize-chunk-size. Default value
|
|
# # of randomize-chunk-range is 10.
|
|
#
|
|
# raw: yes # 'Raw' reassembly enabled or disabled.
|
|
# # raw is for content inspection by detection
|
|
# # engine.
|
|
#
|
|
# chunk-prealloc: 250 # Number of preallocated stream chunks. These
|
|
# # are used during stream inspection (raw).
|
|
# segments: # Settings for reassembly segment pool.
|
|
# - size: 4 # Size of the (data)segment for a pool
|
|
# prealloc: 256 # Number of segments to prealloc and keep
|
|
# # in the pool.
|
|
#
|
|
stream:
|
|
memcap: 32mb
|
|
checksum-validation: auto # reject wrong csums
|
|
inline: auto # auto will use inline mode in IPS mode, yes or no set it statically
|
|
reassembly:
|
|
memcap: 128mb
|
|
depth: 1mb # reassemble 1mb into a stream
|
|
toserver-chunk-size: 2560
|
|
toclient-chunk-size: 2560
|
|
randomize-chunk-size: yes
|
|
#randomize-chunk-range: 10
|
|
#raw: yes
|
|
#chunk-prealloc: 250
|
|
#segments:
|
|
# - size: 4
|
|
# prealloc: 256
|
|
# - size: 16
|
|
# prealloc: 512
|
|
# - size: 112
|
|
# prealloc: 512
|
|
# - size: 248
|
|
# prealloc: 512
|
|
# - size: 512
|
|
# prealloc: 512
|
|
# - size: 768
|
|
# prealloc: 1024
|
|
# - size: 1448
|
|
# prealloc: 1024
|
|
# - size: 65535
|
|
# prealloc: 128
|
|
|
|
# Host table:
|
|
#
|
|
# Host table is used by tagging and per host thresholding subsystems.
|
|
#
|
|
host:
|
|
hash-size: 4096
|
|
prealloc: 1000
|
|
memcap: 16777216
|
|
|
|
# Logging configuration. This is not about logging IDS alerts, but
|
|
# IDS output about what its doing, errors, etc.
|
|
logging:
|
|
|
|
# The default log level, can be overridden in an output section.
|
|
# Note that debug level logging will only be emitted if Suricata was
|
|
# compiled with the --enable-debug configure option.
|
|
#
|
|
# This value is overriden by the SC_LOG_LEVEL env var.
|
|
default-log-level: notice
|
|
|
|
# The default output format. Optional parameter, should default to
|
|
# somenp1s0fing reasonable if not provided. Can be overriden in an
|
|
# output section. You can leave this out to get the default.
|
|
#
|
|
# This value is overriden by the SC_LOG_FORMAT env var.
|
|
#default-log-format: "[%i] %t - (%f:%l) <%d> (%n) -- "
|
|
|
|
# A regex to filter output. Can be overridden in an output section.
|
|
# Defaults to empty (no filter).
|
|
#
|
|
# This value is overriden by the SC_LOG_OP_FILTER env var.
|
|
default-output-filter:
|
|
|
|
# Define your logging outputs. If none are defined, or they are all
|
|
# disabled you will get the default - console output.
|
|
outputs:
|
|
- console:
|
|
enabled: yes
|
|
- file:
|
|
enabled: no
|
|
filename: /var/log/suricata.log
|
|
- syslog:
|
|
enabled: no
|
|
facility: local5
|
|
format: "[%i] <%d> -- "
|
|
|
|
# Tilera mpipe configuration. for use on Tilera TILE-Gx.
|
|
mpipe:
|
|
|
|
# Load balancing modes: "static", "dynamic", "sticky", or "round-robin".
|
|
load-balance: dynamic
|
|
|
|
# Number of Packets in each ingress packet queue. Must be 128, 512, 2028 or 65536
|
|
iqueue-packets: 2048
|
|
|
|
# List of interfaces we will listen on.
|
|
inputs:
|
|
- interface: xgbe2
|
|
- interface: xgbe3
|
|
- interface: xgbe4
|
|
|
|
|
|
# Relative weight of memory for packets of each mPipe buffer size.
|
|
stack:
|
|
size128: 0
|
|
size256: 9
|
|
size512: 0
|
|
size1024: 0
|
|
size1664: 7
|
|
size4096: 0
|
|
size10386: 0
|
|
size16384: 0
|
|
|
|
# PF_RING configuration. for use with native PF_RING support
|
|
# for more info see http://www.ntop.org/PF_RING.html
|
|
pfring:
|
|
- interface: enp1s0f0
|
|
# Number of receive threads (>1 will enable experimental flow pinned
|
|
# runmode)
|
|
threads: 1
|
|
|
|
# Default clusterid. PF_RING will load balance packets based on flow.
|
|
# All threads/processes that will participate need to have the same
|
|
# clusterid.
|
|
cluster-id: 99
|
|
|
|
# Default PF_RING cluster type. PF_RING can load balance per flow or per hash.
|
|
# This is only supported in versions of PF_RING > 4.1.1.
|
|
cluster-type: cluster_flow
|
|
# bpf filter for this interface
|
|
#bpf-filter: tcp
|
|
# Choose checksum verification mode for the interface. At the moment
|
|
# of the capture, some packets may be with an invalid checksum due to
|
|
# offloading to the network card of the checksum computation.
|
|
# Possible values are:
|
|
# - rxonly: only compute checksum for packets received by network card.
|
|
# - yes: checksum validation is forced
|
|
# - no: checksum validation is disabled
|
|
# - auto: suricata uses a statistical approach to detect when
|
|
# checksum off-loading is used. (default)
|
|
# Warning: 'checksum-validation' must be set to yes to have any validation
|
|
#checksum-checks: auto
|
|
# Second interface
|
|
#- interface: enp1s0f1
|
|
# threads: 3
|
|
# cluster-id: 93
|
|
# cluster-type: cluster_flow
|
|
# Put default values here
|
|
- interface: default
|
|
#threads: 2
|
|
|
|
pcap:
|
|
- interface: enp1s0f0
|
|
# On Linux, pcap will try to use mmaped capture and will use buffer-size
|
|
# as total of memory used by the ring. So set this to somenp1s0fing bigger
|
|
# than 1% of your bandwidth.
|
|
#buffer-size: 16777216
|
|
#bpf-filter: "tcp and port 25"
|
|
# Choose checksum verification mode for the interface. At the moment
|
|
# of the capture, some packets may be with an invalid checksum due to
|
|
# offloading to the network card of the checksum computation.
|
|
# Possible values are:
|
|
# - yes: checksum validation is forced
|
|
# - no: checksum validation is disabled
|
|
# - auto: suricata uses a statistical approach to detect when
|
|
# checksum off-loading is used. (default)
|
|
# Warning: 'checksum-validation' must be set to yes to have any validation
|
|
#checksum-checks: auto
|
|
# With some accelerator cards using a modified libpcap (like myricom), you
|
|
# may want to have the same number of capture threads as the number of capture
|
|
# rings. In this case, set up the threads variable to N to start N threads
|
|
# listening on the same interface.
|
|
#threads: 16
|
|
# set to no to disable promiscuous mode:
|
|
#promisc: no
|
|
# set snaplen, if not set it defaults to MTU if MTU can be known
|
|
# via ioctl call and to full capture if not.
|
|
#snaplen: 1518
|
|
# Put default values here
|
|
- interface: default
|
|
#checksum-checks: auto
|
|
|
|
pcap-file:
|
|
# Possible values are:
|
|
# - yes: checksum validation is forced
|
|
# - no: checksum validation is disabled
|
|
# - auto: suricata uses a statistical approach to detect when
|
|
# checksum off-loading is used. (default)
|
|
# Warning: 'checksum-validation' must be set to yes to have checksum tested
|
|
checksum-checks: auto
|
|
|
|
# For FreeBSD ipfw(8) divert(4) support.
|
|
# Please make sure you have ipfw_load="YES" and ipdivert_load="YES"
|
|
# in /etc/loader.conf or kldload'ing the appropriate kernel modules.
|
|
# Additionally, you need to have an ipfw rule for the engine to see
|
|
# the packets from ipfw. For Example:
|
|
#
|
|
# ipfw add 100 divert 8000 ip from any to any
|
|
#
|
|
# The 8000 above should be the same number you passed on the command
|
|
# line, i.e. -d 8000
|
|
#
|
|
ipfw:
|
|
|
|
# Reinject packets at the specified ipfw rule number. This config
|
|
# option is the ipfw rule number AT WHICH rule processing continues
|
|
# in the ipfw processing system after the engine has finished
|
|
# inspecting the packet for acceptance. If no rule number is specified,
|
|
# accepted packets are reinjected at the divert rule which they entered
|
|
# and IPFW rule processing continues. No check is done to verify
|
|
# this will rule makes sense so care must be taken to avoid loops in ipfw.
|
|
#
|
|
## The following example tells the engine to reinject packets
|
|
# back into the ipfw firewall AT rule number 5500:
|
|
#
|
|
# ipfw-reinjection-rule-number: 5500
|
|
|
|
# Set the default rule path here to search for the files.
|
|
# if not set, it will look at the current working dir
|
|
default-rule-path: /etc/suricata/rules
|
|
rule-files:
|
|
- botcc.rules
|
|
- ciarmy.rules
|
|
- compromised.rules
|
|
- drop.rules
|
|
- dshield.rules
|
|
- emerging-activex.rules
|
|
- emerging-attack_response.rules
|
|
# - emerging-chat.rules -- Ignore to allow IRC
|
|
- emerging-current_events.rules
|
|
- emerging-dns.rules
|
|
- emerging-dos.rules
|
|
- emerging-exploit.rules
|
|
- emerging-ftp.rules
|
|
- emerging-games.rules
|
|
- emerging-icmp_info.rules
|
|
# - emerging-icmp.rules -- ignore to suppress icmp messages
|
|
- emerging-imap.rules
|
|
- emerging-inappropriate.rules
|
|
- emerging-malware.rules
|
|
- emerging-misc.rules
|
|
- emerging-mobile_malware.rules
|
|
- emerging-netbios.rules
|
|
#- emerging-p2p.rules
|
|
- emerging-policy.rules
|
|
- emerging-pop3.rules
|
|
- emerging-rpc.rules
|
|
- emerging-scada.rules
|
|
- emerging-scan.rules
|
|
- emerging-shellcode.rules
|
|
- emerging-smtp.rules
|
|
- emerging-snmp.rules
|
|
- emerging-sql.rules
|
|
- emerging-telnet.rules
|
|
- emerging-tftp.rules
|
|
- emerging-trojan.rules
|
|
- emerging-user_agents.rules
|
|
- emerging-voip.rules
|
|
- emerging-web_client.rules
|
|
- emerging-web_server.rules
|
|
- emerging-web_specific_apps.rules
|
|
- emerging-worm.rules
|
|
# - tor.rules -- Ignore these to allow privacy users
|
|
# - decoder-events.rules # available in suricata sources under rules dir -- Ignored for too trigger-happy on UDPv4 checksum
|
|
# - stream-events.rules # available in suricata sources under rules dir -- Ignored for false positives
|
|
- http-events.rules # available in suricata sources under rules dir
|
|
- smtp-events.rules # available in suricata sources under rules dir
|
|
- dns-events.rules # available in suricata sources under rules dir
|
|
- tls-events.rules # available in suricata sources under rules dir
|
|
- local.rules # Custom rules for us
|
|
|
|
classification-file: /etc/suricata/rules/classification.config
|
|
reference-config-file: /etc/suricata/rules/reference.config
|
|
|
|
# Holds variables that would be used by the engine.
|
|
vars:
|
|
|
|
# Holds the address group vars that would be passed in a Signature.
|
|
# These would be retrieved during the Signature address parsing stage.
|
|
address-groups:
|
|
|
|
HOME_NET: "[127.0.0.0/16,10.0.1.0/24,96.41.230.196]"
|
|
|
|
EXTERNAL_NET: "!$HOME_NET"
|
|
|
|
HTTP_SERVERS: "$HOME_NET"
|
|
|
|
SMTP_SERVERS: "$HOME_NET"
|
|
|
|
SQL_SERVERS: "$HOME_NET"
|
|
|
|
DNS_SERVERS: "$HOME_NET"
|
|
|
|
TELNET_SERVERS: "$HOME_NET"
|
|
|
|
AIM_SERVERS: "$EXTERNAL_NET"
|
|
|
|
DNP3_SERVER: "$HOME_NET"
|
|
|
|
DNP3_CLIENT: "$HOME_NET"
|
|
|
|
MODBUS_CLIENT: "$HOME_NET"
|
|
|
|
MODBUS_SERVER: "$HOME_NET"
|
|
|
|
ENIP_CLIENT: "$HOME_NET"
|
|
|
|
ENIP_SERVER: "$HOME_NET"
|
|
|
|
# Holds the port group vars that would be passed in a Signature.
|
|
# These would be retrieved during the Signature port parsing stage.
|
|
port-groups:
|
|
|
|
HTTP_PORTS: "80,443"
|
|
|
|
SHELLCODE_PORTS: "!80"
|
|
|
|
ORACLE_PORTS: "1521"
|
|
|
|
SSH_PORTS: 22
|
|
|
|
DNP3_PORTS: "20000"
|
|
|
|
# Set the order of alerts bassed on actions
|
|
# The default order is pass, drop, reject, alert
|
|
action-order:
|
|
- pass
|
|
- drop
|
|
- reject
|
|
- alert
|
|
|
|
# IP Reputation
|
|
#reputation-categories-file: /etc/suricata/iprep/categories.txt
|
|
#default-reputation-path: /etc/suricata/iprep
|
|
#reputation-files:
|
|
# - reputation.list
|
|
|
|
# Host specific policies for defragmentation and TCP stream
|
|
# reassembly. The host OS lookup is done using a radix tree, just
|
|
# like a routing table so the most specific entry matches.
|
|
host-os-policy:
|
|
# Make the default policy windows.
|
|
windows: ["10.0.1.2"]
|
|
bsd: []
|
|
bsd-right: []
|
|
old-linux: []
|
|
linux: ["127.0.0.1","10.0.1.3"]
|
|
old-solaris: []
|
|
solaris: []
|
|
hpux10: []
|
|
hpux11: []
|
|
irix: []
|
|
macos: []
|
|
vista: []
|
|
windows2k3: []
|
|
|
|
|
|
# Limit for the maximum number of asn1 frames to decode (default 256)
|
|
asn1-max-frames: 256
|
|
|
|
# When run with the option --engine-analysis, the engine will read each of
|
|
# the parameters below, and print reports for each of the enabled sections
|
|
# and exit. The reports are printed to a file in the default log dir
|
|
# given by the parameter "default-log-dir", with engine reporting
|
|
# subsection below printing reports in its own report file.
|
|
engine-analysis:
|
|
# enables printing reports for fast-pattern for every rule.
|
|
rules-fast-pattern: yes
|
|
# enables printing reports for each rule
|
|
rules: yes
|
|
|
|
#recursion and match limits for PCRE where supported
|
|
pcre:
|
|
match-limit: 3500
|
|
match-limit-recursion: 1500
|
|
|
|
# Holds details on the app-layer. The protocols section details each protocol.
|
|
# Under each protocol, the default value for detection-enabled and "
|
|
# parsed-enabled is yes, unless specified otherwise.
|
|
# Each protocol covers enabling/disabling parsers for all ipprotos
|
|
# the app-layer protocol runs on. For example "dcerpc" refers to the tcp
|
|
# version of the protocol as well as the udp version of the protocol.
|
|
# The option "enabled" takes 3 values - "yes", "no", "detection-only".
|
|
# "yes" enables both detection and the parser, "no" disables both, and
|
|
# "detection-only" enables detection only(parser disabled).
|
|
app-layer:
|
|
protocols:
|
|
tls:
|
|
enabled: yes
|
|
detection-ports:
|
|
dp: 443
|
|
|
|
#no-reassemble: yes
|
|
dcerpc:
|
|
enabled: yes
|
|
ftp:
|
|
enabled: yes
|
|
ssh:
|
|
enabled: yes
|
|
smtp:
|
|
enabled: yes
|
|
imap:
|
|
enabled: detection-only
|
|
msn:
|
|
enabled: detection-only
|
|
smb:
|
|
enabled: yes
|
|
detection-ports:
|
|
dp: 139
|
|
# smb2 detection is disabled internally inside the engine.
|
|
#smb2:
|
|
# enabled: yes
|
|
dns:
|
|
# memcaps. Globally and per flow/state.
|
|
#global-memcap: 16mb
|
|
#state-memcap: 512kb
|
|
|
|
# How many unreplied DNS requests are considered a flood.
|
|
# If the limit is reached, app-layer-event:dns.flooded; will match.
|
|
#request-flood: 500
|
|
|
|
tcp:
|
|
enabled: yes
|
|
detection-ports:
|
|
dp: 53
|
|
udp:
|
|
enabled: yes
|
|
detection-ports:
|
|
dp: 53
|
|
http:
|
|
enabled: yes
|
|
# memcap: 64mb
|
|
|
|
###########################################################################
|
|
# Configure libhtp.
|
|
#
|
|
#
|
|
# default-config: Used when no server-config matches
|
|
# personality: List of personalities used by default
|
|
# request-body-limit: Limit reassembly of request body for inspection
|
|
# by http_client_body & pcre /P option.
|
|
# response-body-limit: Limit reassembly of response body for inspection
|
|
# by file_data, http_server_body & pcre /Q option.
|
|
# double-decode-path: Double decode path section of the URI
|
|
# double-decode-query: Double decode query section of the URI
|
|
#
|
|
# server-config: List of server configurations to use if address matches
|
|
# address: List of ip addresses or networks for this block
|
|
# personalitiy: List of personalities used by this block
|
|
# request-body-limit: Limit reassembly of request body for inspection
|
|
# by http_client_body & pcre /P option.
|
|
# response-body-limit: Limit reassembly of response body for inspection
|
|
# by file_data, http_server_body & pcre /Q option.
|
|
# double-decode-path: Double decode path section of the URI
|
|
# double-decode-query: Double decode query section of the URI
|
|
#
|
|
# uri-include-all: Include all parts of the URI. By default the
|
|
# 'scheme', username/password, hostname and port
|
|
# are excluded. Setting this option to true adds
|
|
# all of them to the normalized uri as inspected
|
|
# by http_uri, urilen, pcre with /U and the other
|
|
# keywords that inspect the normalized uri.
|
|
# Note that this does not affect http_raw_uri.
|
|
# Also, note that including all was the default in
|
|
# 1.4 and 2.0beta1.
|
|
#
|
|
# meta-field-limit: Hard size limit for request and response size
|
|
# limits. Applies to request line and headers,
|
|
# response line and headers. Does not apply to
|
|
# request or response bodies. Default is 18k.
|
|
# If this limit is reached an event is raised.
|
|
#
|
|
# Currently Available Personalities:
|
|
# Minimal
|
|
# Generic
|
|
# IDS (default)
|
|
# IIS_4_0
|
|
# IIS_5_0
|
|
# IIS_5_1
|
|
# IIS_6_0
|
|
# IIS_7_0
|
|
# IIS_7_5
|
|
# Apache_2
|
|
###########################################################################
|
|
libhtp:
|
|
|
|
default-config:
|
|
personality: IDS
|
|
|
|
# Can be specified in kb, mb, gb. Just a number indicates
|
|
# it's in bytes.
|
|
request-body-limit: 3072
|
|
response-body-limit: 3072
|
|
|
|
# inspection limits
|
|
request-body-minimal-inspect-size: 32kb
|
|
request-body-inspect-window: 4kb
|
|
response-body-minimal-inspect-size: 32kb
|
|
response-body-inspect-window: 4kb
|
|
# Take a random value for inspection sizes around the specified value.
|
|
# This lower the risk of some evasion technics but could lead
|
|
# detection change between runs. It is set to 'yes' by default.
|
|
#randomize-inspection-sizes: yes
|
|
# If randomize-inspection-sizes is active, the value of various
|
|
# inspection size will be choosen in the [1 - range%, 1 + range%]
|
|
# range
|
|
# Default value of randomize-inspection-range is 10.
|
|
#randomize-inspection-range: 10
|
|
|
|
# decoding
|
|
double-decode-path: no
|
|
double-decode-query: no
|
|
|
|
server-config:
|
|
|
|
#- apache:
|
|
# address: [192.168.1.0/24, 127.0.0.0/8, "::1"]
|
|
# personality: Apache_2
|
|
# # Can be specified in kb, mb, gb. Just a number indicates
|
|
# # it's in bytes.
|
|
# request-body-limit: 4096
|
|
# response-body-limit: 4096
|
|
# double-decode-path: no
|
|
# double-decode-query: no
|
|
|
|
#- iis7:
|
|
# address:
|
|
# - 192.168.0.0/24
|
|
# - 192.168.10.0/24
|
|
# personality: IIS_7_0
|
|
# # Can be specified in kb, mb, gb. Just a number indicates
|
|
# # it's in bytes.
|
|
# request-body-limit: 4096
|
|
# response-body-limit: 4096
|
|
# double-decode-path: no
|
|
# double-decode-query: no
|
|
|
|
# Profiling settings. Only effective if Suricata has been built with the
|
|
# the --enable-profiling configure flag.
|
|
#
|
|
profiling:
|
|
# Run profiling for every xth packet. The default is 1, which means we
|
|
# profile every packet. If set to 1000, one packet is profiled for every
|
|
# 1000 received.
|
|
#sample-rate: 1000
|
|
|
|
# rule profiling
|
|
rules:
|
|
|
|
# Profiling can be disabled here, but it will still have a
|
|
# performance impact if compiled in.
|
|
enabled: yes
|
|
filename: rule_perf.log
|
|
append: yes
|
|
|
|
# Sort options: ticks, avgticks, checks, matches, maxticks
|
|
sort: avgticks
|
|
|
|
# Limit the number of items printed at exit.
|
|
limit: 100
|
|
|
|
# per keyword profiling
|
|
keywords:
|
|
enabled: yes
|
|
filename: keyword_perf.log
|
|
append: yes
|
|
|
|
# packet profiling
|
|
packets:
|
|
|
|
# Profiling can be disabled here, but it will still have a
|
|
# performance impact if compiled in.
|
|
enabled: yes
|
|
filename: packet_stats.log
|
|
append: yes
|
|
|
|
# per packet csv output
|
|
csv:
|
|
|
|
# Output can be disabled here, but it will still have a
|
|
# performance impact if compiled in.
|
|
enabled: no
|
|
filename: packet_stats.csv
|
|
|
|
# profiling of locking. Only available when Suricata was built with
|
|
# --enable-profiling-locks.
|
|
locks:
|
|
enabled: no
|
|
filename: lock_stats.log
|
|
append: yes
|
|
|
|
# Suricata core dump configuration. Limits the size of the core dump file to
|
|
# approximately max-dump. The actual core dump size will be a multiple of the
|
|
# page size. Core dumps that would be larger than max-dump are truncated. On
|
|
# Linux, the actual core dump size may be a few pages larger than max-dump.
|
|
# Setting max-dump to 0 disables core dumping.
|
|
# Setting max-dump to 'unlimited' will give the full core dump file.
|
|
# On 32-bit Linux, a max-dump value >= ULONG_MAX may cause the core dump size
|
|
# to be 'unlimited'.
|
|
|
|
coredump:
|
|
max-dump: unlimited
|
|
|
|
napatech:
|
|
# The Host Buffer Allowance for all streams
|
|
# (-1 = OFF, 1 - 100 = percentage of the host buffer that can be held back)
|
|
hba: -1
|
|
|
|
# use_all_streams set to "yes" will query the Napatech service for all configured
|
|
# streams and listen on all of them. When set to "no" the streams config array
|
|
# will be used.
|
|
use-all-streams: yes
|
|
|
|
# The streams to listen on
|
|
streams: [1, 2, 3]
|
|
|
|
# Includes. Files included here will be handled as if they were
|
|
# inlined in this configuration file.
|
|
#include: include1.yaml
|
|
#include: include2.yaml
|